<
From version < 495.1 >
edited by Fredrik Lagerström
on 2020/03/25 15:59
To version < 496.1 >
edited by Fredrik Lagerström
on 2020/03/25 15:59
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1211,9 +1211,11 @@
1211 1211  |(% style="width:84px" %)[[image:1585065760145-701.png]]|(% style="width:197px" %)[[Point-point connection>>doc:.Point-point connection (Geometry).WebHome]]
1212 1212  |(% style="width:84px" %)[[image:1585065769120-640.png]]|(% style="width:197px" %)[[Line-line connection>>doc:.Line-line connection (Geometry).WebHome]]
1213 1213  
1214 -**[[image:file:///C:/Users/Fredrik/AppData/Local/Temp/msohtmlclip1/01/clip_image003.wmz||alt="MCj04113200000%5b1%5d"]] (% class="wikiinternallink wikiinternallink" %)Edge connection(%%)** is not a “connection object”. It is a definition tool for boundary connection conditions, which is available for (% class="wikiinternallink wikiinternallink" %)**Plate**(%%)/(% class="wikiinternallink wikiinternallink" %)**Wall**(%%), (% class="wikiinternallink wikiinternallink" %)**Profiled panel**(%%) and (% class="wikiinternallink wikiinternallink" %)**Timber Panel**(%%) elements. But, the (% class="wikiinternallink wikiinternallink" %)**non-linear behavior and component settings**(%%) are valid for edge connections introduced for the supports and below mentioned connection elements. See the definition modes and possibilities of an (% class="wikiinternallink wikiinternallink" %)**Edge connection at Plate**(%%).
1214 +|(% style="width:104px" %)[[image:warning.png]]|(% style="width:1386px" %)(((
1215 +(% class="wikiinternallink wikiinternallink" %)**Edge connection**(%%) is not a “connection object”. It is a definition tool for boundary connection conditions, which is available for (% class="wikiinternallink wikiinternallink" %)**Plate**(%%)/(% class="wikiinternallink wikiinternallink" %)**Wall**(%%), (% class="wikiinternallink wikiinternallink" %)**Profiled panel**(%%) and (% class="wikiinternallink wikiinternallink" %)**Timber Panel**(%%) elements. But, the (% class="wikiinternallink wikiinternallink" %)**non-linear behavior and component settings**(%%) are valid for edge connections introduced for the supports and below mentioned connection elements. See the definition modes and possibilities of an (% class="wikiinternallink wikiinternallink" %)**Edge connection at Plate**(%%).
1215 1215  
1216 1216  The end connection property of the bar elements are also not “connection objects”. You can read more about them at the (% class="wikiinternallink wikiinternallink" %)**Beam**(%%), (% class="wikiinternallink wikiinternallink" %)**Column**(%%) and (% class="wikiinternallink wikiinternallink" %)**Fictitious bar** **connection**(%%) settings.
1218 +)))
1217 1217  
1218 1218  For the end points of the edge connections two options are available:
1219 1219  
... ... @@ -1220,17 +1220,18 @@
1220 1220  * Separate end points from environment,
1221 1221  * Connect end point to environment.
1222 1222  
1223 -In all Shell Toolwindows this setting is available by choosing ‘Edge connection’ then clicking [[image:file:///C:/Users/Fredrik/AppData/Local/Temp/msohtmlclip1/01/clip_image051.png||alt="figure_leftMOUSE"]] on ‘End point behaviour’ **//[[image:file:///C:/Users/Fredrik/AppData/Local/Temp/msohtmlclip1/01/clip_image052.png]] //** button. The end point can be chosen in three steps by selecting the Plate or Wall, then the edge and finally the end point.
1225 +In all Shell Toolwindows this setting is available by choosing ‘Edge connection’ then clicking [[image:1585148332414-120.png]] on ‘End point behaviour’ [[image:1585148337443-223.png]]**// //** button. The end point can be chosen in three steps by selecting the Plate or Wall, then the edge and finally the end point.
1224 1224  
1225 -[[image:file:///C:/Users/Fredrik/AppData/Local/Temp/msohtmlclip1/01/clip_image053.jpg]]
1227 +[[image:1585148343595-809.png]]
1226 1226  
1227 -[[image:file:///C:/Users/Fredrik/AppData/Local/Temp/msohtmlclip1/01/clip_image002.wmz||alt="MCj02990090000%5b1%5d"]] Using this function can solve problems like the one on the picture below:
1229 +|(% style="width:88px" %)[[image:light.png]]|(% style="width:1402px" %)(((
1230 +Using this function can solve problems like the one on the picture below:
1228 1228  
1229 1229  On the right side structure all edge connection end points are connected to the environment which cases difference between the shear force on the wall and the sum of shear forces on the plate panels, which should be in balance according to common sense and this is exactly the case on the left side structure where edge connection end points are separated from the environment.
1230 1230  
1234 +[[image:1585148385776-904.png]]
1235 +)))
1231 1231  
1232 -[[image:file:///C:/Users/Fredrik/AppData/Local/Temp/msohtmlclip1/01/clip_image054.png]]
1233 -
1234 1234  == Plastic calculation ==
1235 1235  
1236 1236  The plastic data can be set in the //Default settings/Data tab //of each above mentioned options. The figure shows where the feature is placed in the dialog.
Copyright 2020 StruSoft AB
FEM-Design Wiki